• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Replace Door Locks

Door locks are the first protection against unauthorised access to your home. Signs of wear and tear, and also instances like moving into a new residence or burglaries, could trigger the need to replace your lock.

To begin, determine your cylinder size by measuring the distance between the adjustment screw and the center of the knob lock cylinder. This measurement will assist you purchase the right-sized lock.

Deadbolt

Installing a deadbolt is ideal way to secure your door from burglars. The bolt extends into the strike plate on the doorframe when it is locked, making it more difficult for a burglar to gain entry into the door. A single cylinder deadbolt is activated by keys on the exterior side and a thumb turn part on the interior. A deadbolt will only work if it is installed correctly.

The first step is to determine if the door has a hole for a deadbolt or if it has to be bored. Utilizing the template included with your lock installation kit, mark the location of the hole for the deadbolt on the door's surface. Utilize your tape measure to determine the height of the deadbolt. Mark this height on the door edge and use the speedsquare to draw a straightline across the mark that you made for the bolthole.

Then, use a power drill to drill this area until the hole extends to the opposite side of the door. This may take some time. Then, sand down the hole and the edges of the door so that it's smooth. At this stage, it's a great idea to paint or stain your door.

Remove any visible screws from the deadbolt. This will reveal the front and rear assembly of the deadbolt as well as its internal bolt. Then, unscrew the bolt and replace upvc door lock mechanism Door Lock (Telegra.Ph) it with a new one that matches the door hardware. The bolt is often attached to a set plate which you'll need to unbolt. After this is done then you need to cut out the space for the strike plate on the door frame.

If your strike plate is not in alignment It could be due to the previous installer failed to mortise it correctly or a weatherstripping changed the strike position. You'll need to re-mortise the strike plate and perhaps even the deadbolt to fix the issue. Once this is completed, test the deadbolt by closing it and locking it. Make sure the bolt extends into the strike plate, and then test the key to make sure it is able to open and close smoothly.

Knob

It could make your business and home less secure If the knob on your door is worn. It can also make opening and closing the door more difficult, which is why it is an ideal idea to replace it. replacing upvc door lock and handle the knob is an easy DIY task that should not take longer than 30 minutes to complete. Make use of pliers or a screwdriver to remove any knobs or handles. Be cautious not to scratch other parts of the door.

Spray WD-40, or another dry lubricant, onto the mechanism of your door knob prior to you begin. This will let the new lock to slide effortlessly as you turn it. To ensure proper operation it is important to select the right knob and handle to are compatible with your doors. If you don't already have a doorknob that is compatible and handle, you'll need to purchase a new one.

Before you begin the replacement upvc door lock, take a look at the knob that was previously used to determine what screws are keeping it in place. If there are no screws, you can use the screwdriver to secure the cover plate in between the hidden screws plate.

After you've removed your knob, check it for any indications of damage or rust. It's important to clean it off if you notice any scratches or dents however, you shouldn't need to do anything major when the knob is in good condition.

Install the new knob. First, examine the new knobs to ensure you're selecting the correct one for your door. You'll need to choose one with an extending rod that's designed to lock into the rod mechanism on the second knob. After you've inserted the new knob in the hole, slide it into the latch.

Thread the latch plate screws down and test the spring by pressing down on it several times. The latch should then spring back up every time. Install the second knob and secure it to the rod mechanism of the first knob. Thread the long screws from the interior doorknob through the holes for cylinders on the outside knob and fix it in place.

Latch

A latch is a piece metal that extends through the door jamb to keep it closed. The latch can be operated by a handle or knob located inside the door, or a thumb-turn on the outside. A deadbolt is a device used to secure a latch and keep burglars from piercing the glass of the door. It also protects against accidental or intentional closing of the door by pets or children. You can install a latch with either a single-cylinder deadbolt, or a double-cylinder deadbolt based on the level you prefer for security.

Installing a deadbolt can be the same as installing a latch however there are some differences. To make sure that the new lock will work first, you must measure the setback on the doorjamb with the tape measure. The setback is the distance from the edge of the doorjamb to the middle of the hole that will be used for the faceplate for the latch. The standard setback is 2 3/8 to 2. 3/4 inches. If you have a greater setback, you may need to purchase a longer latch from a hardware shop or locksmith.

The next step is to drill an edge bore hole through the doorjamb for the latch plate. Use a chisel and chisel the latch mortise. Make sure the hole's depth is enough to allow the faceplate to be flush with the doorjamb. Place the strikeplate on the floor to ensure it is positioned correctly.

If the strike is placed too high, the door can be pushed into or pressure imposed on it with a crowbar or tire iron. This can also cause the doorjamb to break. This can be fixed by drilling a new hole through the doorjamb, and cutting the core from the previous one.

The final step is to put in the new strike plate, which can be done by screwing it in place over the existing screw holes. Use wood putty then to fill in any existing bolt holes or screw holes which aren't going to be used. Once the putty is dry, sand it smooth for a professional finish.

Strike

The piece of metal that connects the deadbolt and latch when the door is shut is an electric strike. It is a vital part of the lock's overall safety because it prevents the door from opening, and also provides additional resistance to force or kicking. If a door comes with an electronic strike, it can be opened by using a key and the control unit that regulates the electrical impulses.

In the past, putting in an electronic strike was as simple as cutting a portion of a doorjamb to remove the latchbolt on a cylindrical lock from the pocket within the strike. This modification can be a drawback in regards to the appearance of an opening and also exposes the latchbolt and keeper mechanism to unintentional users.

Recently, a number of electric strike manufacturers have created a new type of electric strike dubbed the "No Cut" strike that doesn't need a cutout in the doorjamb for operation. These strikes have a unique design to allow the latchbolt and keeper to slide into the strike pocket without marring the doorjamb faceplate.

The strike has an internal ramp that raises the latchbolt and keeper whenever it receives an electrical signal from a reader or controller. The latchbolt and keeper are pushed up the ramp due to retract. When the door is shut, the deadbolt stays at a lower position and the latchbolt retracts into the keeper.

Installing an electric strike is an easy process, particularly when you are replacing the strike on a previous door. If you're upgrading an existing access control system to an electric strike, it is important to ensure that your new system is compatible. It is also necessary to make sure that the strike is connected to your access control system and is configured to operate in a fail-safe way.

One way to protect against unauthorized access is to upgrade the strike on your doors to a high-quality strike plate. These plates can be fitted with up to six screws of three inches instead of the usual two screws of three-fourths inches. These screws are longer and make breaking the frame to reach the thumb turn piece on a single cylinder deadbolt more difficult.