• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Reasons Your Fiat 500 Key Fob Won't Work

A key fob with the fiat 500 spare key cost ducato key programming, click for info, 500 number is a convenient way to unlock the doors and get started the car. There are a variety of reasons why the key fob might stop working. These include a dead battery damage to the receiver module, water issues, and interfering.

This listing is for an NEW replacement fiat 500 key cutting Flip Key Remote - like the Ilco brand that must be professionally programmed by a local automotive locksmith (click here for Locksmith Search). It comes with lock, unlock and trunk buttons.

Dead Coin Battery

The most frequent reason that your 500 key fob won't work is an inactive battery. Modern key fobs have a very limited operating range and should be within just a few feet of the car to operate. If you are far from your vehicle and press the keyfob button it will not respond and display the message "Key Fob Not Detected".

If this occurs then replace the battery for your coin-cell (Part Number CR2032) by a fresh one of a reliable brand, such as Panasonic Duracell or Energizer. You can usually find them at your local hardware store, or online.

You can test the coin-cell battery by pressing the buttons while you're standing close to your Fiat 500. The car should flash its parking lights, and the key fob should be able to operate the lock and unlock switches.

If your fob's key doesn't work even after replacing the battery, it may be water damage which hinders it from communicating with the module locked keys in fiat 500 your vehicle. Water damage can occur in a number of ways, ranging from an accidental splash to submerging your fob in salt water at the beach. If you suspect your fob has been exposed to water, you can try placing it in a dry rice bag to pull the moisture out. If this isn't working, you'll require your fob to be reset by an auto locksmith or dealer.

Water Damage

While the fob has some rubber seals to keep water from the chip's electronic circuit, submerging it in the ocean or washing it in a machine could cause water damage. Saltwater is especially dangerous to the circuit board of the fob, causing it to short out and eventually die. In the event that you let your fob get wet, it's not an ideal choice however, if you drop it in the water in a cup or do not remember to take it out of your pocket before you run the washer Don't give up hope.

Take the battery off first. Clean the electronic chip using isopropyl alcohol or another similar product and then dry it thoroughly before replacing the battery. Check the fob again to determine if it's functioning. If the key doesn't work, it may need to be changed. This is usually handled by an auto locksmith or dealer.

If the key you have is older and not programmed to work with your vehicle, you will need to replace it completely. A professional locksmith for cars will be able to complete this process. The locksmith will need the key cut to match your car's ignition. They will also need to reprogram the fob for the car's system. This is a simple and inexpensive process that is usually completed the next day.

Receiver Module Issues

One of the main reasons why your 500 key fob could stop working is that it's simply out of range. The remote usually has a range of 30 feet or less, and if it's too far from your vehicle, it will not respond to your commands. You can easily solve this issue by moving the remote closer to your car until it responds.

If your fob won't work after you replace the coin battery, also called a "button", "watch" or "button", it may be due to a malfunction on the internal circuit board. In most cases, reprogramming the fob can resolve the problem. You can find instructions on how to start a fiat 500x with key to do this for all vehicles by searching YouTube or consulting the owner's manual.

It is sometimes necessary to replace the clips made of metal that hold the coin batteries in their place. If they lose tension it could prevent the coin battery from sitting properly, and this will cause your remote to malfunction.

In rare cases the fob could be out of alignment with your vehicle because of hardware or software problems. You can fix this issue by visiting your local auto-locksmith or dealer to reprogram your key fob. In certain situations it may be necessary to reinstall the program in your body control module as well.

Interference

In addition to a dead coin battery The key fob might not be receiving or transmitting an signal due to interference. This could happen when the keyfob's location is in close proximity to a radio transmitter, like a cell phone or radar detector. The key fob might not work due to a bad connection with the buttons water damage or damage to the internal chips.

If your key fob suddenly stopped working, or you have tried everything at home to resolve it (e.g. replacing the battery, reprogramming, and using the spare key fob, it could have a damaged receiver module on your 500. The receiver module is situated under the dash and receives the radio frequency signals from the key fob. It converts the signals into electronic commands which are then translated by the vehicle.

There is a simple way to reset the 500's on-board system, including the keyfob. Disconnect the battery of 12 volts for about 15 minutes, by removing the negative cable first then the positive cable. Then, reconnect the battery. This will eliminate any remaining electric current, and also restart the car's computer. This could help you get your key fob working again. If the problem persists you should speak with an expert technician. They'll be able to determine the exact cause of your issue.