• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Door Lock Replacement - What You Need to Know

It is a good idea for you to change your locks when they begin to exhibit signs that they're worn out. This could be due to having difficulty turning the lock, or having a key that does not fit.

It is good to know that installing new hardware for your door locks is surprisingly easy. All you have to do is follow these steps.

Deadbolt

The deadbolt is your primary security for your door against forced entry. It is stronger and more secure than the latch which activates the lock. So, you'll want to ensure that the new deadbolt you purchase meets your requirements. If possible, opt for the deadbolt made of case hardened steel that has no exposed screwheads on the exterior to stop drilling by anyone else. To increase security, the inner side of your deadbolt should be drilled into the door frame.

During the process of installation, check that your new deadbolt's bolt is extending smoothly into the strike plate after you shut and lock the door. If not, mortise the bolt into the strike plate using a wood chisel and then install the deadbolt. When you shut and lock your door, be sure that the latch of the doorknob is in line with the deadbolt's hole.

Before you install your new deadbolt, check whether it's the same size of the old one. Most door locks come with a template that shows you how far over the doorknob the bolt should be, but it's always best to consult an expert at an hardware store if you're not sure which backset measurement is suitable for your doors. They will be able to direct you towards models that will work with your doors and existing deadbolt opening.

After you've confirmed that your new bolt assembly is the correct length, insert it into the hole of the door. If your new deadbolt is equipped with a latch faceplate, screw it into place as well. It is a good idea to screw the latch faceplate to the frame with the screws recommended by experts, and also.

Some sets of locks come with a decorative or "dummy" bolt that allows you to install the keyed-deadbolt while still having an operational latch. If you're able to choose, the dummy bolt must be installed using the same screws that are used to mount the faceplate for the latch. This will ensure maximum security.

Some deadbolts have only a single cylinder accessible from inside with the thumb-turn, whereas others come with a double glazed door lock replacement cylinder that allows keyed and unkeyed access. Whatever type you select it's a good idea to buy a commercial-grade lock to ensure the highest security. They are tested to withstand up to 250,000 cycles of closing and opening before they are sold to homeowners.

Latch

The latch is the part of the lock that retracts the bolt to open and close the door. It is usually secured with screws on the sides however it can also be attached to the strike plate of the door jamb. When replacing upvc door lock and handle a door latch, it's important to make sure you get the correct one that matches the hardware you have. You can either put the latch against the existing hardware or look up the label on the replacement lock for composite door. Dunn Lumber offers a wide variety of brands. However, it is recommended to select the same brand that matches your existing hardware. This will ensure that the latch you purchase will fit properly.

Some doors are equipped with a havep instead of the latch. A hasp is a strap with a slot punched into it that fits over the staple. The staple is then attached to the door frame or door with the help of a nail. When the upvc replacement door locks is closed the strap pulls back on the staple and locks into place. Commercial buildings utilize a hasp since it is cheaper than a lock.

Like any mechanism with moving parts, a lock will wear out from frequent use over time. Sometimes, the internal mechanism can start to "stick" and be difficult to turn, making it necessary to replace the entire lockset. Sometimes the exterior doorknob will be damaged and it is important to replace that as well.

If your lock is stuck, you can use some graphite inside the keyhole. You can either spray it on the key or dust it on the inside of the lock, and then operate the lock a few times to incorporate the graphite into the mechanism. You can remove the knob using the help of a screwdriver. This will expose all the parts and allow you to observe what's happening inside the.

Once you've removed all the knobs, look for the two or three cylinder setscrews on the outside of the cylinder. Tighten them by turning them clockwise. It is also recommended to remove the faceplate and replace it. Surface-mounted rim locks include an additional set of cylinder setscrews on the back of the case, which must be removed, as is the cover plate.

Strike Plate

The strike plate is a way to strengthen and upgrade to the locking system. It is affixed above the holes for the deadbolts and master key systems bolts. It keeps intruders at bay by ensuring the latch of the lock is secured in the plate when the bolt is engaged. Apart from enhancing security, a top-quality strike plate can also enhance the longevity of a lock replacement upvc door.

A standard strike plate appears like a flat metal plate with holes or sets of holes cut into it. It is affixed to the door frame usually using screws, which gives the latch something to sink into as it closes. The strike plate has to be precisely aligned with the lockset to provide maximum protection against burglaries.

If a door's strike plate is damaged, it must be replaced as soon as it is possible to ensure that the door is able to close and latch correctly. The first step in replacing the strike plate is to ensure that it is properly aligned with the bolt hole inside the doorjamb. This can be done by placing a piece adhesive tape over the bolt hole and then attempting to test the latch. If the latch does not catch then take off the tape. Then chisel the area to make the strike plate flush with the doorjamb.

Once the area is chiseled out it is crucial to use a longer screw to fix the strike plate. They should be at least three inches long to ensure that they are securely fixed to the stud that is behind the trim board. If you do not install the screws that are longer or the wood inside the doorjamb may split in the event of a kick-in attack by a burglar and make the door vulnerable.

A professional locksmith is able to quickly replace the strike plate that has been damaged or worn. They can also install a new strike plate on the door that hasn't had one before. They can also upgrade existing strikeplates to increase the security of a building as well as its aesthetics. This can help a property owner draw in tenants looking for a safe living environment and peace of mind.

Keys

The key cylinder is the component of your lock that accepts a specific key to move pins into place so the inner handle can be turned. The cylinder is also the most crucial component of your door lock as it carries out the function that locks were designed to protect your family, you and your belongings. It is for this reason that many people choose to have their locks rekeyed instead of being replaced.

It is more difficult to replace locks than to change the handle and deadbolt. A complete change in the lock requires removing the old cylinder and hardware from the door (including the handle in the case of a knob-lock combo) and then installing a new one in its place. While there are a number of DIY-friendly kits that you can use to change a lock yourself, it is recommended that you speak with a professional locksmith to make sure the job is done correctly.

Before you can install the new cylinder and lock it is essential to have the right key for your home. A duplicate key will not function properly and may even cause the lock to fail and make it impossible to open. A professional with experience can help you avoid this by making sure that you have a working, genuine key for your home.

The next step is to remove the faceplate, then the latch plate. To take off the screws that hold them in place, you'll need a screwdriver. If the new plates are going to be identical to the previous ones, you might want to secure them to speed up the process. If you have to replace them, make sure not to overtighten the screws as this could cause them to lose their grip on the door.

After you have removed the plates, you will need measure for the new locks. While most modern locksets can fit on a standard thickness of door, it's recommended to know the measurements of your door in advance to avoid frustration when you go to the hardware store. You should also be aware that doorknob locksets tend to be different sizes from deadbolt locksets. Commercial models may have an additional latch or bolt.